If your Beko washing machine won't start, there's an easy reset process to follow: Locate the start, pause and cancel buttons. Press them all down at the same time for around 3-5 seconds. Your machine should now be reset.

Considering this, how do I reset my Beko wm5101w washing machine?

Now press and hold down the start/pause button and press the on/off on, while holding the start/pause button down for 3 seconds until the start/pause is flashing . Now turn the dial to the spin/drain position keeping the start/pause button pressed, hold for 3 more seconds then release.

Furthermore, how do I reset my washing machine? How to reset the washing machine:

  1. Press POWER to turn the washer off.
  2. Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
  3. With the power disabled, press and hold the START/PAUSE button for 5 seconds.
  4. Plug the washer back in, or turn the circuit breaker back on.

Subsequently, question is, how do I fix my Beko washing machine?

Your Beko washing machine does not start If your washing machine doesn't start, hold the start, pause and cancel buttons down for about three to four seconds. This should reset the machine and allow you to continue. If it does not work you may have to call out an engineer.

Why is my Beko washer not spinning?

It is not possible for the washing machine to achieve full speed when this happens. If an out of balance load is detected, the washing machine will try to re-distribute the load itself and this can take time. If the filter is blocked, it can stop your Beko washing machine from spinning.

Related Question Answers

Where is the error code on a Beko washing machine?

The Beko error code system is very simple it goes from E1 to E18, if you can correct the error yourself then you'll simply need to hold down the start button to clear the error code. Remember though if you can't correct the error or aren't confident enough to attempt it then we can help!

Where is filter on Beko washing machine?

Locate the filter on the bottom right-hand side of the appliance. When you open the filter housing there may be a large amount of water, so if your appliance has a drain tube you can use this to reduce the amount of water in the drum. Place a container under the filter to collect the remaining water.

Why is my washing machine drum not turning?

If your washer fills with water but doesn't agitate, the problem is likely to be a faulty lid switch, a broken belt, or a problem with the motor. 1 Check the washing machine's spin cycle. If this works, the motor is operating and the belt is not broken. If the spin cycle doesn't work, the belt may be loose or broken.

How do I test my Beko washing machine?

With the machine switched off shut the door and turn the dial to the 12 o'clock position. Now press and hold down the start/pause button and press the on/off on, while holding the start/pause button down for 3 seconds until the display shows a number or error code.

Are Beko washers good?

Beko washing machines are about average in regard to reliability. They offer a decent operating life and they tend to be a good value because the appliance comes at a low price.

What does it mean when all lights are flashing on washing machine?

If the wash, rinse and spin function lights all flash at the same time, this would indicate a possible blockage in your filter or waste / drain pipe.

Why is my washer stuck on the wash cycle?

If your top load washing machine (or some older front load washers) is stuck on one continuous cycle and will not advance and forward to the next wash cycle, then most likely the washer timer is faulty and needs replacement. The timer on your washing machine controls all aspects of the wash, spin, and rinse cycles.

How do I drain a washing machine?

Start by unplugging the machine and emptying the water. Bail the water out of the tub, or you can drain the tub using gravity by placing the washer drain hose on the floor near the drain or in a bucket. Clamp the hose to prevent any remaining water from running out.

How long should a washing machine last?

The average life expectancy of a new washing machine is 11 years. Consumer Reports recommends replacing any appliance that's more than eight years old, unless it's a high-end model and has a particular appeal to you. Others suggest replacing any top-loading washer manufactured in 1999 or earlier.

How do you reset a front load washer?

How to reset the washing machine:
  1. Press POWER to turn the washer off.
  2. Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
  3. With the power disabled, press and hold the START/PAUSE button for 5 seconds.
  4. Plug the washer back in, or turn the circuit breaker back on.

Why is my washer not draining or spinning?

If the washer won't drain there might be a clogged pump or hose. It's common for small socks or other small clothing items to get into the water drain system and clog the hose leading to the pump or the pump itself. If the washer won't drain the lid switch assembly might be defective. This is a very common problem.

What's wrong with my Beko washing machine?

If the water is not draining out of your machine, you may have a problem with your: Drain hose: ensure this is not clumped up, folded in on itself or stretched out too far. Filter: this may be blocked. If you feel comfortable opening the filter housing to check it for dirt or blockages, do this.

How do I reset my Beko washing machine wmi71641?

Try resetting the appliance by pressing and holding the start/pause/cancel button for three seconds. If this does not solve the problem, you may need an engineer.

How do you clean a Beko washing machine drum?

Cleaning the drum:

You should regularly clean the washing machine drum as residue from dirt and detergent and bacteria can build up over time. Make sure the drum is empty. Add limescale-remover powder or tablet into the detergent drawer. Run the machine on a cotton cycle at a hot temperature (70°C or above).