6400 – HD receiver
  1. Press SYS INFO on the front of the receiver.
  2. On your remote press and hold SAT until SAT, TV, VCR and AUX light up.
  3. Release SAT, it will start to flash.
  4. Choose a random number from 1-16 and enter it. This will reset the frequency the remote uses to communicate with the receiver.
  5. Press #.
  6. Press Record.
  7. Press Done.

Also question is, how do I reset my Bell Satellite?

How to reset my receiver on Bell TV (6400 HD receiver)

  1. If you can't see any picture on your TV, reset your receiver by pressing and holding the POWER button for 5 seconds.
  2. On your Satellite TV remote, press MENU.
  3. Scroll to and select System Setup.
  4. Scroll to and select Factory Defaults.
  5. Read the warning and select Yes.

One may also ask, how do I fix my bell remote? Reset my Fibe Slim remote to factory default

  1. Turn on your TV.
  2. Turn on your FibreOP TV receiver.
  3. Point your FibreOP TV remote at your TV.
  4. Press and hold the OPTIONS button for 3 seconds until the green TV light blinks twice.
  5. Enter the 0000 using your remote's number buttons. You must enter the code within 10 seconds.
  6. The remote is set back to factory settings.

Also, how do I program my Bell Satellite remote to my TV?

How to program your Bell Satellite TV remote to operate your TV

  1. Turn on your TV and your Satellite TV receiver. Press and hold the options button for three seconds, until the green light blinks twice.
  2. Enter the 4-digit code for your TV's brand (or code 0001 to search all brands).
  3. Press and hold the Power button until your TV turns off.
  4. Let go of the power button and press select.

How do I program my remote to my receiver?

Program Remote

  1. On the front panel of your receiver, press the SYSTEM INFO button. (Buttons are behind the door on the right side of the front of the receiver)
  2. On the front of your remote, press the SAT button.
  3. Press the RECORD button.
  4. Select Done.

Related Question Answers

How do I fix my satellite signal?

9 Steps to Fix Searching for Satellite Signal
  1. Make sure you are seeing the error code 771 on the television screen.
  2. Locate your Access Card behind a small front panel on your DirecTV receiver/box.
  3. Check your satellite dish.
  4. Check your cables.
  5. Press your ‘channel' button up twice then down twice.

How do you reset a strong decoder?

Below are the procedure to restore your Strong decoder to factory reset.
  1. Press MENU on your remote control.
  2. Move to SYSTEM SETTING and press OK.
  3. Go to DATABASE reset and click on your remote control.
  4. Enter pin code which is usually (0000).
  5. Move to FACTORY RESET and press OK on your remote control.

Why is my bell receiver not working?

Make sure your Fibe Internet service is working, then reboot your HD PVR and receivers. On your HD PVR, press and hold the POWER button for 5 seconds (until the red, green and blue lights come on) and wait for the TV service to come back. Repeat the process with your other Fibe TV receivers.

How do I reactivate my bell receiver?

b) Activate your receiver over the phone

Call 1 866 353-0334 and choose the Activate an additional receiver option from the self-serve prompts. Then, follow the instructions to complete your request.

How do I reset my setup box?

To manually reset your Set-Top Box:
  1. Unplug the power cord to your Set-Top Box from the electrical outlet for 15 seconds and then plug it back in.
  2. Wait for the time to appear on the front of the Set-Top Box, then power it on.
  3. Wait several minutes while the Interactive Media Guide updates.

How do I reboot my Bell TV?

Reboot your receiver
  1. Press and hold-down the green POWER button on the front of your TV receiver for 5 seconds (until the red, green, and blue lights come on).
  2. Wait a few minutes for the reboot to take place. You may see a black screen during this time.
  3. Once the reboot completes, content from the channel that you last viewed appears.

How do I reset channels on my TV?

Retuning
  1. Switch on your digital box and/or TV.
  2. Press Menu on the remote control.
  3. Select the Setup or Installation option.
  4. Select the ‘First time installation' option (sometimes called ‘Factory reset', ‘Full retune' or ‘Default settings').
  5. Press OK if your equipment asks if you want to delete all your channels.

Does Bell replace remotes?

If you've lost your Bell Satellite TV remote or it has become damaged and can no longer be used, you can order a replacement: Online. By phone. At a Bell store.

How do I program my Bell 9400 Remote without a code?

9400 – HD PVR Receiver
  1. To find the remote code for the device, open a web browser and go to Bell.ca/tvremotecodes.
  2. Press and hold AUX until SAT, TV and VCR light up.
  3. Release AUX, it will start to flash.
  4. Enter one of the codes for your device, then press #. AUX should flash 3 times.
  5. Try to control the other device.

How do I program my Bell 6131 Remote without the code?

6131 – HD Receiver
  1. To find the remote code associated to your TV model, open a web browser and go to Bell.ca/tvremotecodes.
  2. Press and hold TV until SAT, AUX and VCR light up.
  3. Release TV, it will start to flash.
  4. Enter one of the codes for your TV model, then press #. TV should flash 3 times.
  5. Try to control your TV.

How do I pair my bell Bluetooth remote to my TV?

Program my Bluetooth Slim remote
  1. Turn on your TV.
  2. Turn on your FibreOP TV receiver.
  3. Press the menu button on your remote.
  4. Use the down-arrow button on the remote to scroll to Settings and press the select button.
  5. Use the down-arrow button on the remote to scroll to Remote Control and press the select button.

How do I connect my Bell Fibe remote to the receiver?

How to pair a receiver in the Fibe TV app
  1. Touch Menu to open the side navigation panel.
  2. Touch Settings.
  3. Touch the Pair your receiver button.
  4. Touch Next.
  5. On your Fibe TV remote, press the INTERACTIVE TV button.
  6. From the App launcher, select the Fibe Remote app.
  7. Scroll to and select Pair a device.
  8. Select Next.

How do I program my Bell 9241 remote to my TV?

9241 – HD PVR Plus Receiver
  1. To find the remote code for your TV model, open a web browser and go to bell.ca/tvremotecodes.
  2. Press and hold TV until SAT, AUX and VCR light up.
  3. Release TV. It will start to flash.
  4. Enter one of the codes for your TV model, then press #. TV should flash three times.
  5. Try to control your TV.

What is the code for Samsung TV?

Enter the TV code for Samsung : 0101, and keep trying with Samsung 4 digit and 5 digit remote code list below. The LED light will go off after the correct code is entered.

How do I change my PVR remote to my TV 1?

To set the remote to TV1 mode: press and hold the i button for 3 seconds or until you see the green light blink on TV1 (below the i button). If the green light blinks below BACK, the remote is in TV2 mode.

Why is my remote not working on my TV?

Open the battery compartment on the back of the remote and remove both batteries. Press and hold any button on the remote for 20 Seconds. Release the button and reinsert the batteries properly. If the remote does not work, there may be something wrong with the remote or with the remote sensor on the TV.

How do you clean a TV remote control?

Start by removing the batteries from the back of the remote. Then, dip a cotton cloth into rubbing alcohol and wipe down the entire surface of the controller. Follow up with an alcohol-soaked cotton swab to carefully clean around the buttons. If there's grime inside the buttons, use a toothpick to remove it.

How do I reset my Bell 9400 Remote?

9400 – HD PVR Receiver
  1. If you can't see any picture on your TV, reset your receiver by pressing and holding the POWER button for 5 seconds.
  2. On your Satellite TV remote, press MENU.
  3. Scroll to and select System Setup.
  4. Scroll to and select Factory Defaults.
  5. Read the warning and select Yes.

How do I reset my Bell 6131 Remote?

How to reset my Bell Satellite TV (6131/6141 HD receiver)
  1. 6131 – HD Receiver. Steps to follow: 5.
  2. If you can't see any picture on your TV, reset your receiver by pressing and holding the POWER button for 5 seconds.
  3. On your Satellite TV remote, press MENU.
  4. Scroll to and select System Setup.
  5. Scroll to and select Factory Defaults.
  6. Read the warning and select Yes.