Minwax PolyShadesOilBased Stain & Polyurethane Finish | Minwax.

In respect to this, how do you apply polyshades?

Coat soft, porous woods such as pine or alder with Minwax Pre-Stain Wood Conditioner by applying it with a brush or cloth. Allow it to dry for five to 15 minutes, and then use a dry cloth to remove the excess. Finish the surface with PolyShades within two hours of application of the Minwax conditioner.

Beside above, can you apply polyshades with a rag? Using a rag to apply stain, you‘ll both apply and then remove any excess stain in one step. You have better control as to how much stain you apply and how you distribute it. Using a rag also eliminates the bubbles you get when you apply Polyshades with a brush. Then a second coat of the Polyshades stain was applied.

Subsequently, question is, do you wipe off polyshades?

Typically, I use the traditional two-step method: apply my stain, wiping off the excess liquid before it dries, then the next day apply a clear finish.

What kind of polyurethane do you use on oil based stain?

You may apply the Minwax Water Based Polyurethane over a fully cured Minwax Wood Finish Stain (oilbased).

Related Question Answers

How long does PolyShades take to cure?

30 days

What happens if you stain over stain?

If the object you‘re hoping to stain has been sealed with a topcoat, you won't be able to restain it, but you can go over it with a coating or a colored stain blend. As an alternative, you could color the wood with an oil-based paint, but the opacity of the oil-based paints can hide the grains.

Does second coat of stain darken wood?

Leave the stain on the wood longer before wiping it off. Apply a second coat of stain after the first has dried fully. This will usually produce a darker coloring, but it adds a step to the process and slows production.

Can you stain without sanding?

Not all staining projects require sanding, especially if you purchase new, already sanded cabinets. However, you can also avoid sanding if you wish to re-stain old cabinets that have no major dents or scratches that need intricate repairs. Staining old cabinets gives new life to your kitchen.

How long should polyurethane dry between coats?

In-between Coats

When applying polyurethane, brush along the grain, stretching the polyurethane into as thin a coat as possible. Always allow polyurethane to dry 24 to 48 hours before sanding, to give the surface time to cure and harden.

Can you glaze over stained wood?

You can use a glaze to add color effects to a finished piece of wood; however, applying glaze to unfinished wood isn't recommended, even if the wood is stained. The glaze creates unsightly blotches and patches of uneven color. You can apply gel stain over stained, unfinished wood, though, to deepen the color.

How can I stain my kitchen cabinets without sanding?

Preparation:
  1. Remove cabinets and hinges with screwdriver and clean hinges with dish soap diluted in water.
  2. Scrub/clean all cabinet surfaces and allow to dry.
  3. Sand all surfaces with the sanding block.
  4. Wipe dust away with a damp cloth.
  5. Wipe cabinets with deglosser.
  6. Allow cabinets to dry in dust-free environment.

How do you get stains out of old stains?

For wood previously coated with a clear protective finish:
  1. Clean the existing finish with Minwax® Wood Cabinet Cleaner to remove dirt and grime.
  2. Lightly scuff the clean, dried existing finish with a synthetic sanding pad or #220-grit sandpaper.
  3. Use a bristle attachment on a vacuum to remove all of the dust.

Do you have to sand before using PolyShades?

Surface Preparation:

Before starting, surface must be dry, clean and free of dirt, grease and glue. Sand the wood in the direction of the grain using fine-grade sandpaper (#220) until smooth. Remove all sanding dust.

Can I paint over PolyShades?

You can paint over a surface of polyurethane varnish if you prepare it properly. Polyurethane is typically hard, durable and glossy, and it is these qualities that make a finish vulnerable to chips and flaking. You don't have to remove all the varnish before you start painting.

Do you have to put polyurethane over stain?

Do I have to apply a clear coat after staining? While staining creates a rich, deep color that highlights natural wood grain, it does not provide long-term protection. A polyurethane top coat protects the wood from scratches, stains and water damage.

Is polyurethane and stain good in one?

Slightly thinned, it works better & goes further on the 2nd coat. A real beautiful color. Polyurethane/Stain combination products are one of the best things ever made for they have very good tinting & coating qualities.

How long after staining can I apply polyurethane?

Every finish and stain is different, and drying times can vary widely from brand to brand or product to product. As a rule of thumb, you should wait 24-48 hours to allow the stain to fully dry before applying your polyurethane. If you're extra cautious, you may even choose to wait 72 hours before applying your poly.

How long should stain dry between coats?

Allow it to penetrate for 5-15 minutes, then wipe away the excess with a cloth. For highly absorbent woods, you can then apply a second coat, wait, and wipe away the excess again. Allow the pre-stain to dry for 30 minutes before applying stain, but no longer than 2 hours.

What color is Bombay mahogany?

Specifications
Sub-BrandPolyShades
Manufacturer Color/FinishBombay Mahogany
Color/Finish FamilyPurple
SheenSatin
TintableNo

Should you apply stain with a brush or rag?

The basic rule for getting good results with any wood stain is to apply a wet coat and wipe off the excess before it dries. You can use any tool – rag, brush, paint pad, roller or spray gun – to apply the stain. You can even dip the object into stain or pour the stain onto the wood and spread it around.

Can Minwax PolyShades be thinned?

Minwax Polyshades Thinning. Bruce, you are correct. Mineral spirits is the solvent for Minwax Polyshades. Minwax specifically recommends NOT thinning the poly for two reasons.

Can you stain over Minwax PolyShades?

Stain and Finish Wood in One Step with Minwax® PolyShades®

Bruce has the solution: Minwax® PolyShades®. PolyShades® is a combination wood stain and polyurethane finish, allowing you to get both color and protection in one easy step.

How long does it take stain to dry?

24 hours