When placed through a window, it is meant to exhaust the fumes out of the house. These pipes are often present on wood stoves and an improper installation can be a fire hazard. In order to run the stovepipe out of a window, the proper materials and a plan is needed.

Similarly, you may ask, can you vent a fireplace out a window?

Having a window or pipe to suck outside air for a furnace/burner is the way to go. You need to have the room where the burner is located shut. This way outside air cannot be sucked in throughout the cracks in the house.

Likewise, can you run stove pipe horizontal? The pipe should be as straight and short as possible, with sections properly secured. The horizontal portion of the pipe should rise not less than one-quarter inch to the linear foot, to insure a good draft. You should not pass a stove pipe through a combustible wall for a hook-up with a chimney flue.

People also ask, how do you put a stove pipe together?

Putting Together a Stove Pipe Seam

  1. Set a length of stove pipe flat on the floor with the two open ends of the center seam facing away from the floor.
  2. Push the two sides of the seam together.
  3. Push down and in on both sides of the stove pipe seam until you hear a loud snap.

Can you use single wall stove pipe outside?

Having said that, singlewalled pipe is probably not a good choice for the outside chimney. You want the hot exhaust gases to pass up through the chimney quickly, but if they are cooled once they exit the building you can get the colder gases trying to sink back into the stove.

Related Question Answers

How do you run a flue pipe through a wall?

Cutting the Holes
  1. Position the stove so the back is at least 16 inches from an outside wall.
  2. Attach the 90-degree elbow temporarily onto one end of the long section of chimney pipe.
  3. Locate and mark a stud in the wall at each side of the mark, using a stud finder.
  4. Cut the outline in wood paneling, using a jigsaw.

Can I vent my wood stove horizontally?

For instance, wood-burning stoves will always be vented through the roof of your house, but pellet-burning stoves can be vented vertically through the roof, or horizontally through the wall to the outdoors. Same with gas stovesventing can be routed in either direction – vertically or horizontally.

Does a chimney have to be straight?

If it is a manufactured flue it must be installed according to the manufacturer's instructions. An ideal fireplace flue would be straight, but NFPA 211 allows a flue to offset no more than 30°. In Canada a flue may offset by 45°.

How close to a window can a wood stove be?

A wood stove needs to have at least 36 inches of clearance between an unprotected ceiling and the top of the stove. When installing a wood stove in front of a window, make sure the clearance is at least 36 inches from the glass to keep it from heating up and cracking or getting damaged.

Why does a taller chimney create a better draft?

Obviously in a chimney fire, the wood is the fuel and a match is the flame so the air providing the oxygen comes in the form of the draft. The reason that a taller chimney creates a better draft is really rather simple as the higher up in the atmosphere the chimney reaches, the greater the differential pressure.

How do you install stove pipe over roof?

Chimney Pipe Installation for Wood Stove Through a Flat Ceiling
  1. Step 1: Locating the Center Point for the Chimney Pipe.
  2. Step 2: Locating Where to Cut the Hole Through the Roof.
  3. Step 3: Marking and Cutting the Hole on the Roof.
  4. Step 4: Installing the Adjustable Roof Flashing for Chimney Pipe.
  5. Step 5: Installing the Insulated Double Wall Chimney Pipe.

Can you vent a wood stove out a wall?

For best results, vent wood stoves through an interior wall. Chimneys or stovepipes for wood-burning stoves or fireplaces work on the principle that the hotter the pipe or chimney, the more draft delivered to the fire.

Can you put wood burning stove in basement?

A basement is not a good location for effective space heating. Unfinished basements are particularly bad locations because too much of the heat is absorbed by the walls and lost to the outside. Also, wood stoves operating in basements may over-fire or smolder without anyone noticing.

Does stove pipe need to be sealed?

The pipe connected to a wood or pellet stove should not need sealing unless it has a hole or leak in it. Each section of stovepipe has a female end and a male end to join the pipes together. Permanently sealing off a stovepipe is a different matter altogether.

Does the crimped end of stove pipe go up or down?

Yes, crimped end goes down. If you have an old stove the joint at the stove used to be made such that that one hunk of pipe could not be inserted that way.

How do you cut stove pipe length?

Stovepipe directs smoke and gas from a woodstove to the outside.

How to Cut Stove Pipe

  1. Place the length of assembled stovepipe on the floor, lying on its side.
  2. Pull the tape measure along the stovepipe, and place a mark on the surface of the stovepipe at the length you need to cut the stovepipe with the soapstone.

How do you cut a stove pipe straight?

If single wall, the pipe can usually be opened up and laid flat for a clean cut with straight shears (yellow handle or big straight shears). If the pipe is round you need to use both the red and green shears to cut a strip out of the pipe.

Do you have to use double wall stove pipe?

Single wall black stove pipe needs to be at least 18″ from combustibles, will radiate more heat than double wall black stove pipe (desirable in most cases), costs way less, and can be cut to length if needed. Double wall black stove pipe has a 6″ from combustibles and isn't very hot to the touch.

How long does double wall stove pipe last?

Double Wall Stove Pipe was designed to work with your Stainless Steel Chimney to form a complete Wood Stove Venting system! * If a wood burning appliance is used every day in the heating season, surveys have shown that a single wall stove pipe will need replacement every two or three years.

How high should a chimney be above the roof?

3 feet

How much clearance do you need for triple wall stove pipe?

Can a Triple Wall Flue Pipe Be Used for a Wood Stove? All combustibles should be placed at least 36 inches from the stove.

How hot does double wall stove pipe get?

These pipes only need a 2-inch clearance to combustibles because they remain cool on the outside, while their internal design allows them to withstand temperatures as high as 1,700 or 2,100 degrees Fahrenheit for a limited time.

How long can a stove pipe be?

Maximum overall length of straight pipe: 3 m (10 ft.) The assembly should be as short and direct as possible between the stove and chimney. The use of two 45 degree elbows is often preferable to a single 90 degree elbow because less turbulence is created in the exhaust flow and they result in less horizontal run.