Kiln-Dried-After-Treatment
Agreed. Under the IRC this 19% or less moisture content lumber is called kiln-dried-after-treatment lumber and is perfectly acceptable to be used in structural sheathing, subflooring, or framing.
Beside this, what kind of plywood do you use for subfloor?
While OSB is the most popular structural panel, CDX plywood is the most popular type of traditional or “veneer” plywood. CDX plywood is like other laminate plywoods, but the outer layers of laminate are grades “C” and “D,” which means they are cosmetically rough and contain many imperfections, thus lowering their cost.
is plywood or OSB better for a subfloor? The National Tile Contractors Association and the Resilient Floor Covering Institute both recommend plywood for subflooring and underlayment, because it doesn’t have the risk of swollen edges that OSB does. Plywood also has a slight advantage in stiffness, which means that subflooring panels need not be quite as thick.
Also Know, can sheathing plywood be used for subfloor?
Like Sturd-I-Floor, Rated Sheathing may be plywood or OSB. When used as a subfloor, Rated Sheathing typically requires installation of an additional layer of underlayment on top of it before finish flooring can be applied. The underlayment requirements vary depending on the finish flooring.
What do you use for sub flooring?
Plywood has been a standard subfloor material since the 1950s and remains the preferred subflooring for many builders. Standard plywood can be used for subfloors, but a better material is 3/4-inch tongue-and-groove plywood subflooring.
How many layers of plywood do you need for a subfloor?
Personally, I would also make sure the floor joists are close enough together to give good support. Two plywood layers would span 24 inches in most cases, but if you want to get by with one layer, spacing the joists at 16 inch centers will give you a better floor.
How thick should Plywood be for flooring?
The thickness of your plywood subfloor depends on the joist spans. The National Wood Flooring Association recommends a minimum plywood panel thickness of 7/8-inch for joist spans of 19.2 to 24 inches, and a minimum plywood panel thickness of 5/8-inch for joist spans of 16 inches or less.
Do I need to glue plywood to subfloor?
On the 3/4″ subfloor, you have the right idea. Use subfloor adhesive, and screw 8″ at edges, 12″ in field. For the 1/2″ underlayment, ideally, you want to screw every 6″ all across the panel. Adhesive will help you here, as the subfloor plywood will have voids in spots that will not hold a fastener.
What size plywood should be used for a subfloor?
Plywood and OSB Over Joists
the subfloors need to be thicker. For joist spacing of more than 16 inches up to 19.2 inches on center, the minimum thickness for both plywood and OSB is 3/4 inch. For joists spaced more than 19.2 inches on center, the minimum thickness for plywood is 7/8 inch and for OSB, 1 inch.
How thick should Plywood be under tile?
British Standards recommend a minimum of 15mm thick plywood to be used for over-boarding purposes (any less will not provide the rigidity required). This involves screwing a sheet of plywood over the top of the existing floorboards / chipboard or plywood to provide extra rigidity and a flat surface onto which to tile.
How thick should a subfloor be?
Typically made of plywood or OSB and ranging in thickness from 19/32″ to 1 1/8″ thick, the subfloor is truly structural, second only to joists in this respect. Subfloor holds up all of the above layers of flooring, as well as everything in your house—people, dogs, cats, pianos, furniture. All houses have subfloors.
How do you waterproof a subfloor?
If you do not waterproof the subfloor, moisture can make its way under the subfloor and cause mold growth or other damage.
- Cut the end of the silicone caulk nozzle at a 45 degree angle using a utility knife.
- Install the silicone caulk tube into the caulk gun and push the plunger into the back of the tube.
How do you use floor leveling on plywood?
Apply a latex floor primer to the entire plywood surface using a paint roller. Use a brush for application in smaller areas. Thoroughly cover all areas with one coat of primer to enhance adhesion of the leveling compound to the plywood surface. Allow the primer to dry thoroughly.
What screws to use for subfloor?
Steel Screws
The proper steel screw sizes for securing 3/4-inch plywood to the floor joists are #8, #10 and #12 screws. The number refers to the thickness of the screw. Each is available in lengths from 1 1/4 to 3 inches. Typically, the 3-inch variety is used to secure plywood subfloors.
Can I put new subfloor over old subfloor?
One of the benefits of removing the old flooring is it allows you the chance to fix any loose subflooring or squeaks by re-securing the main subfloor to the floor joists prior to installing the new flooring. With all that being said though the answer is YES you can install New Wood Flooring over the old.
Can I tile on plywood?
While tile can be laid on plywood, do not install tile directly onto the plywood subfloor itself. Use intervening layers of two sheets of plywood.
What is the difference between subfloor and underlayment?
The subfloor is the bottom most structure of the floor. It provides a flat and stable surface and supports the actual floor. Underlayment is different from the subfloor in that it rests between the subfloor and the actual floor.
What type of plywood is used for ceilings?
Standard Thicknesses
Before lumber companies began selling OSB, the standard choice for sheathing a roof with a 24-inch rafter spacing was 1/2-inch CDX plywood – the letters CDX indicate that it is construction-grade material intended for exterior applications.
What is the best subfloor material?
Hardwood flooring: Plywood is the best subfloor for hardwood flooring installation. CDX plywood ranging from 1/2 to 3/4-inch-thick and rated A/C will serve well for any hardwood flooring installation. Tongue-and-groove plywood is available to reduce squeaks and help the subfloor fit together better.
How do I strengthen my floor joists with plywood?
How to Reinforce Joists with Plywood
- Measure the distance from the bottom of the floor to the bottom of the joist.
- Measure the length of the beam.
- Cut four strips of one-inch plywood to the width of the first measurement.
- Drill ¼-inch pilot holes at six-inch intervals down both long sides of each plywood board.
What is the best plywood for bathroom subfloor?
Traditionally, exterior grade plywood has been the subfloor material of choice for many bathroom flooring projects. Plywood is made by gluing alternating layers of wood veneer. CDX plywood (¾”) in particular is used often because it has a high level of resistance to moisture and humidity.
What kind of wood to use for subfloor?
Oriented strand board, or OSB, is a wood structural panel that can also be used for flooring. It is made from shredded strands of wood pressed together with wax and a special adhesive, then hot pressed into a panel with up to 50 layers of strands. OSB can be used for subfloors, although it is not as common as CDX.
Does subfloor need to be tongue and groove?
For subflooring, you use tongue and groove plywood. The tongue and groove are only along the 8 foot edges. On the four foot edges, your seams will fall on joist tops, so no need for tongue and groove.
How thick should a bathroom subfloor be?
Make Sure Your Subfloor is Structurally Stable
The installation guide for 1/4 inch HardieBacker recommends having wood subfloors made of 5/8 inch exterior grade plywood or OSB (oriented strand board) that is 23/32 inches thick.
