Top Load Washer – Hydrowave Motor Reset
  1. Unplug the washer for 1 minute from the electrical outlet.
  2. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
  3. The motor has now been reset and is ready for you to start a cycle.

Correspondingly, how do I reset the control panel on my GE front load washer?

Make sure that the control for the washer is not locked. If it is, press and hold the LOCK button for 3 deliberate seconds (or until the control unlocks). There is not another way to reset the control board other than completely unplugging the washer as you have been doing.

Additionally, is there a reset button on GE washers? To reset washing machines that use the GE Hydrowave system, start by unplugging the washer for one minute. Plug the washing machine back in and then within 30 seconds, quickly open and close the lid six times. Raise the lid at least 2 inches and make sure it closes each time. This should complete the motor reset.

Beside above, how do you reset a washing machine?

How to reset the washing machine:

  1. Press POWER to turn the washer off.
  2. Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
  3. With the power disabled, press and hold the START/PAUSE button for 5 seconds.
  4. Plug the washer back in, or turn the circuit breaker back on.

How do I reset my front load washer?

Unplug the washer from the power outlet or turn the circuit breaker to the unit off. With the power disabled, press and hold the START/PAUSE button for 5 seconds. Plug the washer back in, or turn the circuit breaker back on.

Related Question Answers

How do I check the error code on my GE front load washer?

To enter the error code test mode on a GE front load washer, rotate the control knob until t02 is displayed in the control panel then press start/pause to enter the test mode. This is where all error codes are stored.

How do I troubleshoot my GE front load washer?

How to Troubleshoot a GE Front Load Washer That Won't Spin or Drain
  1. Remove any kinks in the drain hose.
  2. Inspect the household drain.
  3. Check the drain and make sure there is an air gap between the hose and drain.
  4. Clean the pump filter.
  5. Rearrange the clothing in the load.
  6. Allow the washer to cool down for two hours.

How do I reset my GE washer WiFi?

First, let's try to disconnect your WiFi module. To do this, please wake up your control by pressing the Power button and then press and hold the “Volume” and “Basket Light” buttons for approx. 3 seconds until the WiFi LED stops blinking. This will turn the WiFi module OFF.

Why is my washing machine drum not turning?

If your washer fills with water but doesn't agitate, the problem is likely to be a faulty lid switch, a broken belt, or a problem with the motor. 1 Check the washing machine's spin cycle. If this works, the motor is operating and the belt is not broken. If the spin cycle doesn't work, the belt may be loose or broken.

How do you troubleshoot a washing machine?

Remove the power source to the washer before troubleshooting or attempting repairs.
  1. #1 – Washer Won't Turn On.
  2. #2 – Not Draining Properly.
  3. #3 – Will Not Spin and/or Agitate.
  4. #4 – Washer Leaking Water.
  5. #5 – Does Not Dispense Detergent.
  6. #6 – Washer is Shaking and Moving.
  7. #7 – Washer is Noisy.
  8. #8 – Washer Smells.

How do I know if my washing machine motor is bad?

The five most common signs of motor issues are listed below.
  1. Washer Won't Pump or Spin. It may happen that the washing machine fails to pump water in and out, as well as spin.
  2. Pumps, but Won't Spin.
  3. Washer Won't Agitate.
  4. Clothes Still Wet.
  5. Problems in Every Cycle.

How long can you pause a washing machine for?

You can pause the cycle. If you stop the cycle it takes 30+/- seconds for the lock mechanism to release.

Why is my washer not draining or spinning?

If the washer won't drain there might be a clogged pump or hose. It's common for small socks or other small clothing items to get into the water drain system and clog the hose leading to the pump or the pump itself. If the washer won't drain the lid switch assembly might be defective. This is a very common problem.

What does calibrating a washing machine do?

When you calibrate your Samsung washing machine, you prevent the appliance from vibrating and making a lot of noise. Calibrating your washing machine can be done via the display and takes 3 minutes maximum.

Why does my GE washer keep pausing?

The door latch can cause a GE frontload washer to pause during a cycle. If the door physically opens, the washer will pause. However, if the door stays locked but the switch is bad then the control will think the door is open and the washer will pause. If the door will not latch then the washer will not start.

How do I calibrate my washing machine?

  1. Press Power to turn on the washing machine.
  2. Press and hold Smart Control for 3 seconds.
  3. Press the Up/Down arrows to select Calibration. Then, press OK.
  4. Press Start/Pause to start Calibration.
  5. The door will be locked during the operation.
  6. When complete, the washing machine turns off automatically.

How do you reset a GE dishwasher?

To reset a GE dishwasher, press the Start or Reset button during a cycle. If you have a top-loading dishwasher, you'll need to open the top, press the button, and close it again. Then, wait 2 minutes for the dishwasher to pump out the water.