How do you adjust the transmission band on a Dodge Ram?

Automatic Transmission Band Adjustment:

Loosen band adjusting screw locknut. Then back locknut off 3-5 turns.
Using Inch Pound Torque Wrench C-3380-A, a 3-in.
Back off adjusting screw the number of turns listed below for your transmission.
Hold adjusting screw in place and tighten lock-nut to:

Also, how do you adjust the bands on a 48re transmission?

to the rear band adjusting screw (1).

Raise vehicle.
Remove transmission oil pan and drain fluid.
Loosen band adjusting screw locknut 5-6 turns.
Tighten adjusting screw to 8 N·m (72 in.
Back off adjusting screw 3 turns.
Hold adjusting screw in place and tighten locknut to.

Beside above, how do you tighten a 47re band? Locate the front band adjustment screw on the driver side of the transmission just forward of the transmission range selector linkage. Loosen the locknut using a 3/4″ socket and back off 3 to 5 turns. Tighten the adjustment screw by rotating it clockwise with a 5/16″ square drive socket.

People also ask, how do you change a transmission band?

Rear Band

Raise the vehicle.
Remove the transmission oil pan.
Loosen the band adjusting screw locknut 5-6 turns.
Tighten the adjusting screw to 72 in.
Back off the front band adjusting screw by the following amounts:
Hold the adjuster screw in position and tighten the locknut to 25 ft.

What are bands in a transmission?

The bands in a transmission are, literally, steel bands that wrap around sections of the gear train and connect to the housing. They are actuated by hydraulic cylinders inside the case of the transmission.

What is adjusting transmission bands?

The inside surface of the band is lined with a friction material similar to that of brake shoes. When the band is applied, it grips the drum firmly and halts the rotation of the drum. This action causes the transmission components to interact in different ways for separate tasks.

How does a 48re transmission work?

The 48RE transmission has electronic shift controls and a four-speed gear layout, including overdrive. For example, it engages the torque converter lockup and does not allow overdrive. This is to prevent excessive speed when towing heavy loads and to conserve fuel.

What is a 48re transmission?

The 48RE four speed automatic transmission represents an evolution of the previous 47RE model and can be found mated to the Cummins Turbodiesel in Ram pickups from 2003 to 2007 model years. The 48RE automatic transmission features an actual input torque rating between 560 and 570 lb-ft of torque.

What is shuttle shift 48re?

To clarify, shuttle shift is the transmissions inability to figure out what gear it wants at a given time. Call Sun Coast Diesel Transmissions and request 1 Dodge 618 Upgrade Governor Pressure Solenoid Kit and 1 Governor Pressure Transducer.

How do I identify a 48re transmission?

Look for the serial number on the left side of the transmission case, just above the oil pan gasket surface. The dealer should be able to confirm from that, what transmission you have. If you paid for a 48re, and you have a 47re, tell them to replace the transmission.

What transmission is in a 2004 Dodge Ram 2500 Cummins?

Smart Buy Price

Engine	5.7L V-8
MPG	City / Hwy
Seating	3 Passengers
Transmission	5-spd man w/OD
Power	345 @ 5400 rpm

What happens when a transmission band breaks?

Transmission bands can become worn and broken, which can cause transmission slipping as well as engine troubles and worn out gears. Bands are what link the gears in the automatic transmission together. To fix this problem you need to replace or adjust the defective band.

Can a transmission be adjusted?

Automatic Transmission Band Service

Transmission band adjustment used to be a regular part of a basic transmission service. Not so much any more: While the bands are still adjustable, the adjustment is usually part of a rebuild and doesn't need to be performed again during the transmission's operating lifetime.

What does the front band do in a transmission?

Automatic Transmission Band Adjustment:

The front band controls the 2nd gear cluster. The rear band controls the 3rd gear cluster and reverse. For a 2-3 shift, the transmission shifts back to 1st gear with the front band while the rear band engages 3rd gear.

How much does it cost to replace transmission bands?

Average Cost of Rebuild, Repair, and Replace:

According to Transmission Repair Cost Guide readers, the average cost of transmission replacement ranges from $1800 to $3400. A used/salvage transmission ranges from $800 to $1500, a rebuilt transmission from $1100 to $2800 and a remanufactured from $1300 to $3400.

How do you adjust automatic transmission?

Rotate the transmission shift lever counterclockwise (toward the front of the transmission) to the first (Park) position, then turn it clockwise (rearward) to the 2nd detent (Neutral) position.
Holding the rod tightly in the swivel, tighten the retainer which was loosened to allow the adjustment.

What causes a transmission to slip?

What Causes a Transmission to Slip? Low fluid levels – The most common cause for slipping is low fluid levels. Worn or broken transmission bands – Transmission bands can become worn or broken, which can cause your transmission to slip. Bands are what links the gears in the automatic transmission together.

What transmission is in a 98 Dodge Ram 1500?

New ListingAutomatic Transmission 4WD 8-318 5.2L Fits 98-99 DODGE 1500 PICKUP 3565240 (Fits: 1998 Dodge Ram 1500)

How do you adjust the transmission band on a Jeep Grand Cherokee?

Jeep Grand Cherokee Front Band (kickdown) Adjustment

Disconnect the negative cable on the battery.
Raise the front of the vehicle with a jack.
Locate the adjusting screw locknut on the left side of the transmission.
Tighten the screw to the specified torque with a torque wrench.
Hold the screw with a pair of pliers.

What are the signs your transmission is going out?

If your car suddenly starts giving off vibrations and strange noises like grinding or whining, the transmission is saying, “Drive me to a mechanic.” You‘ll also experience gears slipping – when the engine speeds up or revs, but your car doesn't accelerate very quickly, or move at all (that's a really bad sign).

What does a transmission band look like?

As the name implies, a transmission band is a steel strap. The strap wraps around the outside of a round drum. Typically, the drum rotates any time the band is not applied. The inside surface of the band is lined with a friction material similar to that of brake shoes.

Is it worth to replace transmission?

√ Generally speaking, repairing a car is almost always less costly than buying a new one. Even a major repair like a blown engine or failed transmission can be repaired/replaced for considerably less than the cost of a new vehicle.

What is line pressure in automatic transmission?

The automatic transmission line pressure control system comprises a line pressure regulating means for regulating line pressure for selectively coupling and uncoupling the friction coupling elements so as to shift the automatic transmission into desired speed gears.