Install a Toilet Seat with Quick Attach Hardware
  1. Place the toilet seat on the toilet.
  2. Insert the bolt through the top side of the toilet seat hinge and push the wing nut from the underside until it meets the bowl (Fig. 1).
  3. Tighten with a screwdriver from the top.
  4. Snap on the hinge cover to complete the toilet seat installation.

Regarding this, how do you unscrew a stubborn screw?

How to Loosen a Stuck Screw

  1. Make sure you've got the right size and shape of screwdriver.
  2. Be sure you're turning the screw in the proper direction.
  3. Put some penetrating oil or WD-40 on the screw and let it sit for a while.
  4. Apply some heat directly to the screw head using an electric soldering gun or a propane plumbing torch.

Likewise, how do you remove a stripped screw from a toilet seat? Place the end of a putty knife against the screw at the bottom of the toilet, above the plastic nut. Tap the end of the putty knife with a hammer, digging the knife into the screw. Continue tapping until the putty knife cuts through the screw, then lift up the seat and screws.

Then, how do you remove a screw that won't move?

Steps

  1. Switch screwdrivers. When a screw is stripped, attempt to remove it with a different screwdriver.
  2. Tap the screwdriver into the head with a hammer. Place your screwdriver into the head.
  3. Remove the screw with a pair of pliers.
  4. Drill a small hole into the head with an electric drill.
  5. Use a Dremel.

How do you remove a stubborn toilet seat?

First, take a look at the bolts that secure the seat. If the bolts or nuts are plastic, they can't corrode and will come off easily. Simply pry open the cover behind the seat to expose the bolt's head. Unscrew the bolt with a pliers or a screwdriver while you hold the nut underneath with the pliers.

Related Question Answers

Can a slow close toilet seat be repaired?

While fairly maintenance-free, they may require a little adjusting from time to time. While the lowering action on most softclose seats cannot be adjusted, it's easy to make minor adjustments to the seat hinges if they become loose and the seat comes out of alignment or starts to slide around on top of the bowl.

How do quick release toilet seats work?

The soft close hinge works with the seat and the lid to help stop them dropping too quickly. The seat is in a white plastic. The quick release mechanism makes cleaning easy.

How do slow close toilet seats work?

A slow close toilet seat is basically one that closes on its own as soon as you start to push it down. Gravity controls it but special, tensioned hinges control the gravity. This is where the slow part comes in so there's no slamming down. To get the seat on its way to closing, even just a light tap will do the trick.

How do you fix a Kohler quiet toilet seat?

Replace the Hinges on a Cachet Quiet Close Q3 Toilet Seat
  1. Remove the toilet seat in the closed position from the toilet (Fig.
  2. Position the toilet seat upside-down on a flat surface.
  3. Using a needle nose pliers, pull each damper inward to release the hinge assembly from the toilet seat.
  4. Remove the grey or black cover from the new hinge assembly.

What is a quiet close toilet seat?

Innovative features include technology that prevents lids from slamming and seats that remove easily for cleaning. The Cachet QuietClose toilet seat with Quick-Release functionality is engineered to close with the slightest touch, reducing unwanted noise often associated with lid slamming.

How do you stop a soft close toilet from creaking?

There's an easy fix for your squeaky toilet seat using common household tools.
  1. Close the toilet lid.
  2. Find the nuts under the back of the toilet bowl.
  3. Repeat with the second nut and screw.
  4. Squirt a small amount of spray lubricant into the hinges at the back of the toilet seat.
  5. Wipe away excess lubricant with a damp rag.

How do you tighten a toilet seat with no access underside?

The procedures to tighten the toilet seat
  1. Step 1: Exam the toilet closely one again. For the majority of the cases, your toilet probably did have holes for underside access.
  2. Step 2: Re – align the seat.
  3. Step 3: Tighten the bolts.
  4. Step 4: Check the tension and close the lid.

How do I change the bolts on a toilet seat hinge?

Standard metal hinge with residential Sta-Tite®
  1. Thread the bolt into the hinge.
  2. Push the bushing all the way up bolt until it's flush with the hinge.
  3. Place toilet seat bolts into toilet bowl.
  4. Finger-tighten Sta-Tite® nut onto bolts.
  5. Align toilet seat onto bowl and use a 1/2″ wrench to tight bolt.

Are all Kohler toilet seats the same size?

There are industry standards for toilet seatsall toilets have seat post holes on 5 1/2″ centers – all elongated bowls are 18 1/2″ from seat posts to front of rim, and all round bowls are 16 1/2″. Any manufacturer's seats will fit any toilet manufacturers bowls if they are standard round or standard elongated.

How do I know what model my Kohler toilet is?

Remove the lid of your toilet tank and check the inside of the tank for the Kohler model number. The model number always consists of four numbers beginning with a “3” or “4” and may or may not have a letter “K” preceding it.

Are there different size round toilet seats?

The height of your toilet doesn't necessarily influence your toilet seat measurement. However, the shape and style make a difference. Round toilets and oval toilets (referred to as elongated toilets) have standard sizing. US-made toilets also have different sizing from European ones.

How do I install the bold look on my Kohler toilet seat?

Install a Toilet Seat with Quick Attach Hardware
  1. Place the toilet seat on the toilet.
  2. Insert the bolt through the top side of the toilet seat hinge and push the wing nut from the underside until it meets the bowl (Fig. 1).
  3. Tighten with a screwdriver from the top.
  4. Snap on the hinge cover to complete the toilet seat installation.

How do you measure for a new toilet seat?

Measure the width of the bowl at its widest point. Be sure to place your measuring tape on the outside of the brim for an accurate dimension. Measure the length of the bowl from between the seat bolts to the outside edge of the front of the bowl. If you have a round bowl, this dimension should be about 16.5 inches.

What does Top fixing mean on a toilet seat?

Top Fixing Toilet seats

Top fixing toilet seat hinges work by feeding two bolt fixings into the toilet pan and tightened from the top, hence the name. You could think of this as something like a wall plug in a hole in the wall.

How do you stop a toilet seat from moving?

A sliding toilet seat is one such problem. You should be able to stop it from sliding by tightening the nuts holding it to the bowl, but they loosen again after a short time and the problem reoccurs. The reason is that the holes for the bolts are purposely oversized so that the bolts won't crack the porcelain.

Are toilet seat fittings standard?

Modern toilets have standard hole centres. Replacement toilet seat kits usually have adjustment to allow fitting to the older or non standard types as well. It is essential that the new seat is supported by the pan at all the contact points.