To program a RAM key fob, you must already have a functioning key fob. During the 30-second programming sequence, you can add up to three additional key fobs. Turn your key to the ON position, but don't start the engine. For 4-10 seconds, press and hold both the unlock button and the panic button at the same time.

Also question is, how do I program my Dodge Ram 1500 key fob?

How to Program a Dodge Ram Key Fob

  1. Enter your car, and turn the ignition to the “Run” position.
  2. Hold the “Unlock” button for 10 seconds, then press and release the “Panic” button as you release the “Unlock” button.
  3. Wait for another chime, then press any button on any other remote you would like to program to sync them to the system.

Furthermore, how do I reset my Dodge Ram key fob? How to Reprogram a Dodge Key Fob

  1. Sit in your car with your remote and your key FOB.
  2. Insert your key into the Dodge ignition and turn the key to the “Run” position.
  3. Press and hold the “Unlock” button on your remote for four seconds and press the “Panic” button while still holding the other button.

can you program a Dodge key fob?

Dodge Key Fob Programming Guide Put your Dodge key into the ignition. Turn the key to the “RUN” position. Once the car cycles its locks, press down the “LOCK” and “UNLOCK” buttons. Release each button, and after that, just press and release the “UNLOCK” button.

How do you program a Dodge key fob with only one key?

Simply follow these four easy steps:

  1. Climb inside your vehicle with your key fob in one hand and key in the other, and quickly press the “LOCK” button on your fob.
  2. Put your key into the ignition, and turn it to the “RUN” position while pressing and holding the remote's “UNLOCK” button at the same time.

Related Question Answers

Where can I get my key fob programmed?

Lower-Cost Key Fob Options

“Many of these less advanced fobs can be programmed by a local mechanic, an automotive locksmith, or the customer.” We found that retailers including Amazon.com, Walmart.com, and KeylessOption.com offer numerous low-cost remotes.

How much does it cost to program a Chrysler key fob?

Call the dealer or locksmith – Explain to them you already have the key/remote and would like it to be cut and/or programmed. Ask them for the quote on this procedure. In addition, keep in mind, the process usually cost somewhere between $80-$150, depends on the type of key/remote you have.

How do you program a key fob?

Key Fob Reprogramming in General
  1. Replace the batteries inside the key fobs.
  2. Get Inside the Car.
  3. Turn on the Ignition.
  4. Press the Lock Button on Remote.
  5. Listen for a Lock Sound.
  6. Programming Additional Remotes.
  7. Turn Off the Ignition.
  8. Step out from your car and test the result.

How do you program a key fob for a 2014 Dodge Ram 1500?

Press and hold the unlock button on a currentlt programmed transmitter for a minimum of four seconds and a maximum of ten seconds. While pressing the unlock buttor, press and release the panic button. Release the unlock button and a single chime will sound. This indicates that the module is in programming mode.

How do you program a Chrysler key fob?

How to Program a Chrysler Keyless Entry Remote
  1. Press the lock button on your Chrysler remote five consecutive times at brief two second intervals.
  2. Place your key in the car's ignition and turn it to the right two clicks to the “Run” position on all Chrysler cars.
  3. Hold the unlock button.
  4. Press and release both the lock and unlock buttons at the same time.

How do you erase memory from a key fob?

Locate the key fob you want to delete, and then hit the check box on the left to select it. Then hit the “Delete” button at the bottom of the screen. Confirm that you want to delete the sensor by selecting “Ok”.

Can you program a new key fob yourself?

Yes. An auto locksmith can handle every step of replacing a key fob. They can get you a new one, program it, and perform any other fob related task. If you need a key fob replacement, it is in your best interest to choose to get your service from a locksmith.

Can you program a key fob without the original?

You don't need to go to a dealership to have your fob programmed but a professional locksmith IS REQUIRED if the original is not available. They are MUCH cheaper than any dealership when programming is needed.

How much does it cost to program a Dodge key fob?

Transponder key programming starts at $50 – $75. This includes keys for GM, Ford, Dodge, Honda, Toyota, Nissan. Remote or fob programming starts at $65.

How do you program a Dodge key fob with one key?

How to Program a Dodge Key Fob
  1. Enter your car and press and release the “Lock” button on your remote five times in about ten seconds.
  2. Insert your key into the ignition and turn it to the “Run” position, then press and hold the “Unlock” button on the remote.
  3. Continue holding the button and press and hold the “Panic” button for one second.

How do you program a key fob for a 2011 Dodge Durango?

How to Program a Dodge Durango Remote
  1. Sit down in your Durango and close all the doors. Place your key in the ignition and turn it to the “Run” position.
  2. Hold the “Unlock” button on the remote you want to program for five seconds.
  3. Press and release the “Unlock” and “Lock” button on the remote at the same time.
  4. Press and release the “Unlock” button.

Do you have to reprogram a key fob after changing the battery?

The key fob will need to be reprogrammed to the vehicle as when the battery was replaced in the key fob, the key was reset. This is why nothing is working with the key fob. After replacing the battery in the key fob remote, you will need to reprogram the remote to the vehicle.

How do you program a 2010 Dodge Ram key fob?

Step-by-Step How To Programming Instructions:
  1. INSERT the first working FOBIK remote key into Ignition.
  2. TURN Ignition to the ON position for at least three (3) to fifteen (15) seconds.
  3. TURN Ignition to the OFF position and REMOVE key.
  4. WITHIN fifteen (15) seconds, INSERT second working FOBIK remote key into Ignition.