Where is the model number on a Trane furnace?

The easiest way to look Trane tonnage model number is on the AC unit itself. Go to the condensing unit on the outside and look for the data plate stamped on the actual side of the compressor. Find the model number. Within this string of letters and numerals, you should find an even, two-digit number.

You can find the model and serial numbers (M/N and S/N) for your furnace by removing the top-front service panel and looking to the left side of the interior cabinet or the top of the blower deck, depending on whether your system is an 80% or 90% AFUE unit.

The model and serial number can be found on the rating plate on the inner wall of your furnace or air handler. A dealer should be involved in accessing the serial number.

This Trane (American Standard) style began use in 2002. It consists of at least 3 or 4 digits at the beginning of the serial number. From 2002 to 2009 the first digit represents the year. The next two digits represent week. Starting in 2010, the first two digits represent year, and the next two digits represent week.

How To Find The SEER Rating. Head over to your cooling system and look for a yellow and black “energyguide” sticker, which can usually be located on the side of the condenser. If this sticker is still in tact, it will tell you the Seasonal Energy Efficiency Ratio in large numbers.

Remove the front door and look inside the unit. You should see the model number printed on rating-plate or decal.

Look for a sticker or tag that gives a date when the furnace was last serviced. This is usually common on gas furnaces and may list the date that the furnace was installed. This can often give a close approximation of the unit’s age. Call the manufacturer to get the age of the furnace.

The most common way to to determine the carrier ac age is through the serial number. In the above style, the determining factor is having a letter in the middle of the serial number. The first two digits are the week of manufacturer. The second set of digits are the year of manufacture.

Look for the 5th and 6th digit of the model number, or approximately that location. It will be a number divisible by 6 or 12, and represents the nominal BTU of the system in thousands. A ton of air conditioning equals 12,000 BTU, and 48 divided by 12 equals 4, so the data plate below indicates the system is 4 tons.

Trane uses alpha codes in their serial numbers to determine the age of manufacture. This HVAC company started this in 1987 with the letter B and skipped a couple of letters during the years. The first letter of the Trane serial number nomenclature gives the year of manufacture and the next two numbers are the week .

Carrier/Payne/Bryant Carrier systems made in the last 20 years or so encode the week and year of manufacture within the first 4 digits. The first 2 are the week of the year (1-52) and the second are the year. For example 0199 would mean the system was made the first week of January in 1999.

For example, a 700- to 1,500-square-foot home will require a BTU rating between 40,000 and 60,000, which will cost between $2,000 and $3,000. A furnace for a home ranging in size from 2,000 and 5,000 square feet will need between 125,000 and 150,000 BTUs and will cost in the neighborhood of $3,300 to $6,500.

Trane’s XR series central air conditioning units are Trane’s mid-model systems. These A/Cs offer efficiency up to 18 SEER and sound decibel ratings as low as 68 dBA. The XR series A/Cs are generally more efficient and quieter than Trane’s XB series entry level air conditioners.

If the trane serial number is a 9-digit combination of letters and numbers, the first number is the year. The heating and air conditioning company made changes again in 2010. The age of the trane serial number is determined by the first two digits.

One difference that you may find between 14 SEER and 16 SEER units is that the 14 SEER units generally have a single-stage compressor while the 16 SEER units often have a two-stage compressor. … Not only does the two-stage compressor make your HVAC unit more energy-efficient, it also allows for longer run-times.

Seer stands for seasonal energy efficiency ratio. 13 Seer is the federal minimum to be sold, is single stage, and cheaper than the higher seer conditioners. … The 16 seer is more expensive initially but saves you money in the long run by lowering your energy costs and has less of an impact on the environment.

Changing a 6 SEER unit over to a 14 SEER unit will use 56 percent less power. This means that it will cost 56 percent less to operate the unit. … Going from a 13 to 14 SEER unit saves about 7.2 percent in power costs. The mandatory move from 13 to 14 SEER is also great for the environment.

According to most manufacturers and heating professionals, as well as This Old House, the average furnace will need to be replaced every 15 to 20 years, as long as the system is properly maintained.

A Carrier HVAC system should last anywhere from 15 to 25 years. However, this can vary depending on several different factors. You will want to make sure that you keep up with several different things to ensure the full functionality and long-term life of your heating and air system.

1. Option one: Open Settings > About Tablet > Status > Serial Number.
2. Option two: For most products, the serial number can be viewed at the bottom of the device back cover.

The date of production/manufacture or age of Tempstar® HVAC equipment can be determined from the serial number located on the data plate.

You can determine the size in tons of your Tempstar HVAC system by examining the model number on the data plate at the side of the condenser (outdoor unit). Look for two numbers in the middle of the model number that are divisible by 6 or 12, and represent the nominal BTU of the system in thousands.

It manufacturers, markets, and sells residential heating and cooling systems under the Arcoaire, Comfortmaker, Day & Night, Heil, KeepRite, Lincoln, and Tempstar brands; its commercial units, with up to 25 tons of cooling capacity, are sold under the ICP Commercial brand.

Look on the back side, the side facing toward the house, and you should find a nameplate. The nameplate lists the manufacturer’s specifications on it. At the top of the nameplate, you should see the manufacture’s date like a month and year. Sometimes it’s abbreviated as MFR DATE.

Though the lifespan of a home air conditioner varies based on many factors, those that are well-maintained should last 10 to 15 years. And by completing regular checkups and repairs – both big and small – many systems can last even longer.

The first two digits represent the year the furnace was made, and the second two represent the month. For example, a furnace with the serial number “040852398” tells you that the furnace was manufactured in 2004 in the month of August.

While it is always necessary to replace both air conditioning components at the same time (in a split system), it’s not always necessary to replace both AC components and the furnace. … Adding a furnace during your air conditioner replacement will cost a lot less, around $1,000 to $3,000.

Age of your Furnace If your furnace is pushing 25 years or more, it’s probably nearing the end of it’s effective lifespan. … You might choose to replace a 15 year old furnace, or it could last more than 30 years.

Having a furnace that’s too big for your space is extremely inefficient. There are two simple signs that indicate that your furnace is most likely oversized: Your furnace runs for a short period of time before shutting off. Your home has uncomfortable hot and cold rooms.