Why is my Whirlpool Duet dryer not starting? whirlpool duet dryer will not start just beeps.
If your Whirlpool dryer won’t spin properly, the drum rollers may be worn out. You can check the rollers for wear and tear to see if they turn easily. If any of the drum rollers are damaged or don’t spin easily, we recommend replacing all of them at the same time as a preventative measure.
If your Whirlpool dryer displays a “PF” error code, indicating a recent power failure, the dryer will need to be reset and restarted. This is done by pressing “Start” for a few seconds to restart the dryer. If the dryer does not restart automatically, select a new cycle and any options then press “Start” to begin.
If it’s the motor buzzing/humming when the start button is pushed then it likely has a bad motor. Open the door and manually reach in and rotate the drum in the counter clockwise direction for a couple of complete revolutions and then shut the door and see if the dryer will start.
A broken drive belt is the most common reason a dryer won’t spin. … A working belt should provide some resistance, so if the drum turns very easily and loosely, the belt is probably broken. Unplug your dryer and remove the lid so you can inspect the belt to confirm that it’s broken.
A broken power cord, failed push-to-start switch or a bad timer can also prevent the dryer from starting. Some dryers use a motor relay to control the drive motor, so a broken motor relay can prevent the dryer from starting. … In electric dryers, a blown thermal fuse can keep the dryer from starting.
Many dryers are equipped with a reset button on the control panel.
Remove the back access panel on the dryer, and look for the exhaust duct near the bottom of the unit. The thermal fuse is either circular or oblong, often white plastic with black material in the center and two wire leads. The thermal fuse is mounted on the exhaust duct.
- Dryer Won’t Start. Of course, there are many possible reasons your dryer might not respond when you push the start button. …
- Dryer Stops Before Clothes Are Dry. …
- Belt Noises. …
- Drum Won’t Turn.
If it is a small problem like a dryer belt, you might be able to get a professional to fix it for around $70. For larger problems like a busted drum, repair costs might be more than $400.
Motor. Gas and electric dryers have a motor that turns the blower and the dryer drum. A defective motor can produce a variety of sounds, such as a ratting noise from a loose pulley, a high-pitched noise from a bad bearing or bushing or a humming noise from a bad winding or switch on the motor.
The drum bearing is located at the rear of the dryer behind the dryer drum. If the drum bearing becomes worn, the drum will rub against the back of the casing and cause a squealing or grinding noise. To check the drum bearing, the dryer cabinet will need to be removed and the drive belt taken off the dryer drum.
That could be a pulley in the motor that’s come loose. If a bushing or bearing in the motor is damaged, you may hear a high-pitched whine. And a hum can come from one of the switches or windings on the motor if it is broken. Unplug the dryer and remove the blower wheel or drum belt if need be, to get to the motor.
If your dryer is not spinning but still getting hot, your clothes will remain damp. The dryer drum is spun by a belt that’s connected to the dryer’s motor. The motor engages the belt to spin the drum. Problems with the dryer not spinning often involve the motor and belt.
Most of these machines rely on air passing through the heater, which in turn regulates the amount the heater element burns(and in most cases the turning of the drum/motor/belt has something to do with making this airflow. Without the airflow, it should either cut out, or burn out.
Sometimes a Whirlpool dryer not starting is more of a power issue than a dryer malfunction. … Make sure the dryer is correctly plugged into the proper electrical outlet. Check for tripped breakers or blown fuses. If needed, reset any tripped breakers and replace blown fuses.
Resetting your dryer is easy. Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the dryer (usually 1 to 5 minutes at most), and then power it up again. That’s it. That’s all it takes to reset.
Heat and controlling heat are essential to the dryer’s function. … A faulty or broken thermostat can make a dryer stop working. Replacing the fuse or the thermostat will allow the dryer to work again. A blown thermal fuse from overheating indicates an additional problem, such as improper ventilation.
The Whirlpool Duet Dryer F01 error may be able to be fixed with a simple reset of the main control. Unplug the dryer for 1 minute and plug it back in this will reset the control if the error persists after that you will need to check the dryer thermal fuse.
- Turn on the tumble dryer main power.
- Within 10 seconds turn the program selector from off to teh 6 o’clock postion, pointing straight down.
- Push the “Start” button three times.
- Turn the program selector to the “one” position which should be the CW or airing program.
A PF (Power Failure) error code indicates that the drying cycle has been interrupted by a power failure. Touch and hold START to restart the dryer cycle or press POWER to clear the display.
- Unplug your dryer and ensure it is no longer connected to the gas or electric.
- Locate the thermal fuse, as above.
- Disconnect the thermal fuse from the wires.
- Test the fuse with a multimeter.
- If the needle on your multimeter does not move, your thermal fuse is blow.
PartMaterial CostTotal CostThermal fuse$5-10$80-$130Dryer thermostat$3-20$180Bearing$50$130-$250Roller$10-30$90-$230
Multimeter Test Remove the two wire leads from the thermal fuse and touch a multitester probe to each wire terminal on the fuse. If you get a reading of infinity, the fuse is fine. Any reading less than infinity indicates a triggered thermal fuse you will need to replace.
When Belt Breaks Over time, wear can weaken the belt until it reaches its breaking point. When a dryer belt breaks, the drum no longer turns to tumble the clothes in the dryer’s hot air. This means clothes won’t dry even if the dryer’s heater and electric motor continue to function.
The average dryer lasts about 13 years. The average residential dryer will last 13 years.
One of the most common causes for a clothes dryer to fail is a broken drive belt on the dryer drum. This is an easy do it yourself repair, which uses very few tools, and can save a lot of money.
This item Whirlpool 341241 Dryer Drum Belt, WhiteWhirlpool 4392065RC 29-Inch Dryer Repair KitCustomer Rating4.7 out of 5 stars (932)4.6 out of 5 stars (939)Price$704$34.26$34.26Sold ByCashwell ApplianceAmazon.comColorwhiteOther
The dryer belt goes around the outside of the drum and is looped onto a drive pulley attached to the dryer motor shaft which drives the belt, and around an idler pulley which applies tension to the belt. This tension is what causes the belt to grip the outside of the drum in order to rotate it.
It’s universal at a reasonable price. All you need to know is the size of your dryer belt. … if you search dryer drive belts you will find out that they sell three different size belts. A 92 1/4″ belt, an 87 3/4″ belt and a 93″ belt.
When the dryer belt starts to go bad, you might hear new and unusual noises when your dryer is running. If you hear a thumping or any other noise, it’s a good idea to track down the problem and fix it before your dryer stops working completely. When the belt breaks, the dryer stops spinning.
Tub rollers are the most common cause for a noisy Whirlpool dryer. Tub rollers are what the tub rolls on and when they are bad the dryer will make a roaring or squealing noise. To check the tub rollers, first unplug the dryer then take the lint filter out and remove the two screws that are under the filter.
The first indication of bad dryer motor bearings is a squealing sound from the dryer. … The noise usually comes from the vicinity of the motor that is typically affixed to the bottom of the dryer, at the back. The bearings might also squeak rhythmically as the dryer drum turns.
The scraping noise could be caused from a small hard object stuck between the front or rear drum seals and bulkheads. It could also be a worn drum support roller or shaft, something stuck in the blower housing or it could be the belt idler pulley.